Products

HV Test Set AC, DC and AC/DC

  • MEGGER T 22/1 | HV AC Test Set up to 75kV RMS

    The AC Voltage Test Set T 22/1 is a portable test set consisting of two separate units: the control unit and the high-voltage unit. This division enables the operator to use the test set on site without transport aids. The test set can be equipped with a rectifier attachment for DC voltage testing up to 80 kV.

    View More
  • MEGGER HPA 100 HPA 130 DC | HV AC Test Set up to 100kV

    The AC Test Set HPA 100 is a powerful test set. The unit has been designed for mounting in cable test van and can be used for testing of cable systems and for burning down high-resistance cable faults with a high breakdown voltage. The test set can be equipped with a rectifier attachment for DC testing up to 130 kV. Since the own noise-level of the test system is below 1 pC, it is also suitable as a voltage source for PD-measurements.

    View More
  • MEGGER 5/15kV DC | Dielectric Test Set

    The dc Dielectric Test Sets measure leakage current while applying a dc voltage at or above the insulation system's operating level. This measurement aids in determining the insulation system's ability to withstand overvoltages such as lightning strikes and switching surges.

    View More
  • MEGGER HV Test Set 50 / 80 / 110kV | Portable HV DC Test

    The HV Test Set is a cable tester for DC voltage testing of cables and cable installations in accordance with the international standards. It consists of an operation unit and HV unit. Due to its small size and low weight the test sets can easily be transported and used on-site. The HV Test Set is available in three versions (50/80/110 kV DC).

    View More
  • MEGGER T 99/1 | Portable HV DC Test 40kV for Cable

    he high voltage test unit T99/1 is a portable and powerful test device able to generate a DC voltage of up to 40 kV. The T 99/1 is used for testing of cables, cable accessories, plant and installations. Because of the short-circuit proof design and high output current of the T 99/1, this is device is also suitable for cable fault location (in conjunction with a TDR unit).

    View More
  • MEGGER HPG70-K | Portable 70kV HV DC Test System

    The high voltage test set HPG 70-K from SebaKMT is a fully insulated test set for DC testing up to 70 kV. Thanks to its fully insulated design this system is ideal for stand-alone applications. The DC voltage is obtained through a bridge rectifier which ensures a very low ripple of the test voltage. Moreover the DC voltage is measured on the secondary side and therefore ensures a precise output voltage.

    View More
  • MEGGER T 26/1 | High Voltage Test System up to 800kV for Cable

    The T 26/1A and T 26/1B high-voltage test sets are efficient, mobile systems for high-voltage testing of cables, cable systems and installations as required by current regulations (VDE) with DC voltages of up to 400 kV and 650 kV respectively. The sets are suitable for both installation in measuring trailers and onsite testing as stationary test set. The spatial separation of the operating and high-voltage units makes it possible to operate the sets from outside the immediate danger area. Their modular structure makes them easy to set up on site and allows adaptation to measuring tasks. The sets are primarily designed for power supply companies, cable laying firms and cable manufacturers for the DC voltage testing of high-voltage systems and cables. Their short-circuit-proof output circuit and high power make them suitable for use in fault location as a burn-down unit for burning high-impedance and intermittent cable fault.

    View More
  • Megger HV Tester 25kV | Portable HV DC Test

    The HV Tester 25 kV is a high-voltage generator with a variable negative DC output voltage of 0 - 25 kV. The condition of the test object with regard to electrical strength and insulation quality can be determined on the basis of the unit's readings for output voltage and current. Due to its small size and internal battery this test-system is ideal for test-conditions where no external power supply is available.

    View More
  • Megger HV Test Set 70 / 120 / 160kV | Portable HV DC Test

    High Voltage DC Dielectric Test Sets provide the most dependable, portable DC highvoltage sources for checking the quality of electrical power cables, motors, switchgear, insulators, transformers and capacitors.

    View More
  • MEGGER HPA 35/50/78 | HV AC Test Set up to 78kV

    The AC voltage test sets HPA 35 to 78 are suitable for 50 Hz AC testing of test objects with a low capacity. In addition to 50 Hz AC testing these units can also be enhanced to a DC test set, (see DC-Test Systems). Typical application areas: - Testing of switchgear - Testing of current-transformers - Testing of MV plant/ component testing

    View More
  • MEGGER Highpot Tester | AC and AC/DC HV Test up to 5kV dc

    The AC and AC/DC High-Pot Testers are designed for safety and ease of operation, and readily adapt to development, maintenance and production testing. Three models are available: two ac and one ac/dc. These instruments test the dielectric strength of electrical insulation and the ground circuit continuity of three-wire appliances and other devices. They feature front-panel adjustable leakage current trip, one-second or continuous testing, and automatic failure shutdown.

    View More
  • MEGGER HPG 50/70/110-H | Portable HV DC Test Sets

    The High Voltage test sets HPG 50 to 110-H are suitable for 50 Hz AC-testing (35 to 78 kVRMS) and DC-testing up to 110 kV. The HPG 50 to 80-D are suitable for 50 Hz AC testing (35 to 58 kVRMS) and DC testing up to 150 kV*. The HPG test systems consist of two separate units: the control unit and the high-voltage unit. This separation enables the operator to use the test set on-site without any complications.

    View More